The commissioning record for an air conditioner – who asks for it and why it pays
Roman Oškrobaný · · 8 min read
On a split installation you often hear "we'll fill in the protocol". But which law asks for it? None – not in Slovakia, not in Czechia, not in the EU. The law wants a certified company and technician, a filled-in F-gas label and the added refrigerant in the equipment record. The commissioning protocol is wanted by the makers, for their warranty – and it should be wanted by every technician who stands behind their work. This post sets out exactly what the law asks, what each maker asks, and what the record should hold so that it still helps you with a warranty claim three years from now.
What the law asks
The F-gas rules come from Regulation (EU) 2024/573 and its implementing acts, in Slovakia from Act 286/2009 Coll. and in Czechia from Act 73/2012 Coll. For installing a split they mean this:
Who may install: a certified technician only. That includes joining a pre-charged split on site. A company that installs for others needs its own company certificate.
A1 or A2: an A2 certificate covers charges under 3 kg only (hermetically sealed equipment under 6 kg). A split or multi-split holding 3 kg or more, counted with the refrigerant added on site, needs a technician with an A1 certificate.
The F-gas label: where refrigerant can be added on site, the label has room for the added amount and the total charge. The technician fills both in before putting the unit into operation.
The equipment record: the refrigerant and its amount, with the refrigerant added at installation shown separately, plus the company that installed the equipment, its certificate number and the technician's name. The operator keeps it for 5 years and the installing company keeps a copy. This duty starts at 5 t CO₂ equivalent of HFCs or at 1 kg of R1234yf, also inside a blend: about 7.4 kg of R32, 2.4 kg of R410A, and about 3.2 kg of R454B (through its R1234yf share). So most R32 splits are below it – but the numbers on the label are the same ones.
A leak check right after installation is no longer in EU law: Regulation 1516/2007, which asked for it, was repealed from 23 July 2026 without a replacement. Checking the joints after opening the valves is still the makers' instruction and good practice.
Slovakia: the company needs a certifikát (valid 1 year) and its technicians an osvedčenie (valid 5 years). By 31 January the company reports how much refrigerant it charged into new equipment.
Czechia: only a certified person may install. A seller may sell a pre-charged split to an end customer only with a written contract that names the unit's serial number and says a certified person will install it. The seller keeps it for 5 years.
A commissioning protocol is not on this list. Standards such as EN 378 are voluntary in both countries (STN EN 378 in Slovakia, ČSN EN 378 in Czechia), so even the pressure test and the vacuum are not legal duties on their own. The makers' installation manuals ask for them – and so do their warranties.
What the makers ask
This is where the protocol really appears. Not with every maker, and not always in the same way:
Warranty and commissioning (checked 18 November 2026)
Maker
What it asks
Mitsubishi Electric (Slovakia, CS-MTRADE)
The warranty starts at commissioning (at the latest 3 months after the goods were taken over), done by a licensed company and a technician with an SZ CHKT certificate. 24 months with a service at least once a year. 60 months if the installing company hands the seller the filled-in start-up protocol with the measured values within 15 days of the first start, or registers the unit at zaruka.vykuruj.sk and uploads the protocol there. Every claim needs the type, the serial number and the protocol.
Daikin (Czechia, Slovakia)
No paper form. Up to 7 years (Sensira 5) if an authorised Daikin partner installs the unit and registers it in Stand By Me; the customer confirms by email. Then a service every 2 years by an authorised partner.
Panasonic
UK terms: 5 years if an accredited installer registers the unit on PRO Club within 30 days. The Czech leaflet 2026 gives a 5-year compressor warranty with no commissioning condition.
LG (Czechia, Slovakia)
Nothing to send. The 10-year compressor warranty asks for maintenance once a year by an authorised installer.
Hyundai (Klimavex)
Registration within 30 days of installation for the longer warranty; a service once a year, otherwise 12 months.
Samsung, Gree, Toshiba, Midea, Inventor, Vivax
We found nothing for Slovakia or Czechia. Read the warranty card that comes with the unit, or ask the distributor.
Warranty terms change every year or two. Before you promise a customer anything, look at the maker's current terms.
The makers' forms differ. The Mitsubishi Electric protocol from CS-MTRADE has two pages: the serial numbers of the outdoor and indoor units, the start-up date, the company, the responsible person, signature and stamp, five rows for the later yearly services, and the values measured after at least 15 minutes of running (current, air temperatures, the pressure at the service valve, pipe length, refrigerant added). Daikin's checklist calls itself a guideline, not a warranty condition – but for a claim Daikin wants the installation date from the protocol, the pipe length and the height difference between the units.
None of these forms has a box for the nitrogen pressure test or the vacuum.
Why write down more than the form asks
Always fill in the maker's form when the maker has one – otherwise you risk a shorter warranty for the customer. But a complete record of your own pays off even where the maker asks for nothing:
Proof of good work. When a compressor fails two years on, the question is: was the installation right? A record of the pressure test, the vacuum and the test run from the day of installation is stronger than "we did it the way we always do".
What a claim needs. Pipe length, height difference, added refrigerant and the start-up date are exactly what the makers ask for in a claim. Three years later nobody remembers them.
One number everywhere. The added and the total refrigerant go on the F-gas label, into the equipment record and into the yearly report. Write them down once, at installation, and they will never differ.
A difference the customer can see. An installation without a pressure test and vacuum is quicker and cheaper, and at first sight you can't tell. A sheet with the measured values and your signature is the reason a customer pays for honest work. And a customer who got one will ask other installers for it next time.
What the record should hold
In the order you do it on site:
Nitrogen pressure test: a short strength test, then a tightness test of at least 15 min with the pipe temperature at the start and at the end, never above the PS on the nameplate. The nitrogen test calculator judges the result.
Vacuum: to the vacuum depth the installation manual asks for, and a hold test for as long as the maker asks. The vacuum calculator knows each maker's rules.
Refrigerant and valves: the grams added for the pipe beyond the pre-charged length, both service valves fully open, caps tightened. Write down the added and the total amount – they go on the label.
Joint check at both units, now under refrigerant: with an electronic detector or bubbles. Write down which.
Electrical: voltage, breaker and RCD as the manual asks, cable sizes, earth, polarity and insulation resistance – Mitsubishi Electric asks for at least 1 MΩ at 500 V.
Test run: long enough to settle (the steadiest readings come after 12–25 min). Air temperatures at the indoor and outdoor unit, current, the pressure at the service valve, no error code, no unusual noise. On a multi-split, each indoor unit on its own. Diagnose judges the readings.
Installation and handover: outdoor unit level on anti-vibration pads, clearances kept, condensate drain tested with water, pipe insulation closed, wall hole sealed, F-gas label filled in, the customer shown how to use the unit and clean the filters, the manual, the warranty card and the record handed over.
In the ClimaToolkit app, Commissioning on a unit's page under Units and F-gas leads you through these steps in this order and prints the record as a PDF. The app never stores customers' names or addresses: the PDF has an empty box to fill in by hand, two signature lines and five rows for the yearly services.
What to tell the customer
Do the maker's registration the same day, where the maker has one (Mitsubishi Electric in Slovakia within 15 days, Panasonic PRO Club within 30 days, Daikin Stand By Me, Hyundai within 30 days). The deadline is easy to miss.
Tell them what the warranty asks of them: usually a service once a year (every 2 years for Daikin). Without it, the longer warranty is lost.
Hand them the record. A customer who keeps it in a drawer will pull it out at the first claim – and your name with it.
E1 or EL01 on a Midea, Vivax or Inventor split: the indoor and outdoor units can't talk to each other. How to read the code, what usually causes it and what to measure, in order.
What applies in 2027 to installing and servicing air conditioners: EU Regulation 2024/573, the Slovak Act 286/2009, the Czech Act 73/2012 and its amendment, certificates, records and bans.
Half an hour? An hour? How long to evacuate a split, what the makers ask, why you need a micron gauge, and how the hold test tells moisture from a leak.