Vivax error codes
The app finds the right code table from the model number on the nameplate.
Open in the appMidea – new 4-character codes (current R32 units)
- AERI PRO / AEMI PRO / AEQI PRO / AEGI PRO / AEXI PRO / AEFI PRO
- AENI (N+)
- AEHI+ (H+)
- COFM multi
EH00, EL01, PC04 …), from Midea's EX R32 service manual (2025) and Midea's 2019 slides on the new code system. Use it for current Midea R32 splits (Oasis Plus, All Easy Pro, Breezeless, Xtreme Save, Solstice, Solunar, M2OH / M3OE indoor units) and Midea-built Vivax units whose display shows 4 characters (AERI / AEMI / AEQI PRO, COFM multi).
How to read codes on this unit
The indoor display shows the 4-character code, sometimes with a gap ( EL 01). 1st letter: E error, P protection, F fault, L frequency limit. 2nd letter: H indoor, C outdoor, L other.Units without a display flash the lamps instead: the run lamp flashes (2 Hz) a number of times, and the timer lamp is off, on or flashing. Some codes share one pattern ( EH60andEH61;EC51toEC54): for those, read the display or engineering mode.Not errors: FordFdefrost ·CLactive clean ·FP8 °C heating ·FCforced cooling ·APWi-Fi AP mode ·CPswitched off by the remote.Engineering mode (remote RG10E27): hold POWER + FAN for 7 s (the remote shows 0); ▲ / ▼ picks a channel. Exit with POWER + FAN for 2 s, or wait 60 s.Channels: 0 current error code, 1 T1, 2 T2, 3 T3, 4 T4, 5 TP, 6 target Hz, 7 actual Hz, 8 current, 9 AC volts ÷ 10 … Not confirmed: this channel list comes from the manual's text and was not checked against the printed page. Older remotes: use the information inquiry instead: within 10 s press LED ×3, then SWING ×3. Items: T1, T2, T3, T4, Tb, TP, TH, FT, Fr, IF, OF, LA, CT, ST. Garbled or unknown code: first make sure it is not a temperature. If the unit ignores the remote → indoor PCB; if it obeys → display board. Many codes have an old 2-character equivalent on older Midea units (e.g. EL01=E1). The old compressor-drive sub-codesP40…P49arePC40…PC49here.
Codes on the indoor display
EH60 and EH61; EC51 to EC54), so those patterns are not confirmed.
EH00 Indoor EEPROM malfunction EH0A Indoor EEPROM parameter error EL01 Indoor ↔ outdoor communication error EH02 Zero-crossing detection error EH03 Indoor fan speed out of control EH60 Room sensor T1 open or short EH61 Indoor coil sensor T2 open or short EH0b Indoor PCB ↔ display board communication error EL0C Refrigerant shortage detected (leak detection) EC51 Outdoor EEPROM parameter error EC52 Outdoor coil sensor T3 open or short EC53 Outdoor ambient sensor T4 open or short EC54 Discharge sensor TP open or short EC56 Indoor coil outlet sensor T2B open or short (multi split) EC07 Outdoor fan speed out of control PC00 IPM module protection or IGBT over-current PC01 Over- or under-voltage (DC bus P–N out of range) PC02 Compressor top or IPM over-temperature PC03 High or low pressure protection (units with pressure switches) PC04 Inverter compressor drive error PC08 Over-current protection -- Indoor units in conflicting modes (multi split) FH0P Wi-Fi AP mode active, but no Wi-Fi module fitted
Extended list (engineering mode)
EH30 Indoor external fan parameter error EH35 Indoor external fan phase loss EH36 Indoor external fan current-sampling bias EH37 Indoor external fan zero speed EH38 Indoor external fan stall EH39 Indoor external fan out of step EH3A Indoor external fan DC bus voltage low EH3E Indoor external fan over-current EH3F Indoor external fan hardware over-current EC55 Outdoor IPM temperature sensor (TH) fault EC71 Outdoor fan over-current EC72 Outdoor fan phase loss EC73 Outdoor fan zero speed EC74 Outdoor fan current-sampling bias EC75 Outdoor fan hardware over-current PC10 Outdoor AC voltage too low PC11 Outdoor DC bus voltage too high PC12 Outdoor DC bus voltage too low PC40 Main chip ↔ driver chip communication error PC41 Compressor current-sampling circuit fault PC42 Compressor start failure PC43 Compressor phase loss PC44 Compressor zero-speed protection PC45 Voltage drop (compressor loses power) PC46 Compressor speed out of control PC49 Compressor over-current PC06 Discharge pipe high temperature PC0F PFC failure PC30 High pressure protection PC31 Low pressure protection PC0L Low outdoor temperature protection PC0A Condenser high temperature PH09 Anti-cold-air in heating PH0c Humidity sensor fault PH90 Evaporator high temperature protection PH91 Evaporator low temperature protection
Frequency limits (not faults)
LH00 Frequency limited by indoor coil temperature T2 LH30 Frequency limited by indoor fan current LH31 Frequency limited by indoor fan voltage LH07 Frequency limited by the remote control LC01 Frequency limited by outdoor coil temperature T3 LC02 Frequency limited by discharge temperature TP LC03 Frequency limited by current LC05 Frequency limited by voltage LC06 Frequency limited by IPM temperature LC30 Frequency limited by high pressure LC31 Frequency limited by low pressure
Midea – old 2-character codes (about 2017–2019)
- AENI (N+)
- AEHI+ (H+)
- AEYIs (Y)
How to read codes on this unit
The indoor display shows the 2-character code. Units without a display flash the lamps instead: the run lamp blinks a number of times, and the timer lamp is off, on or flashing. Information inquiry (live readings): within 10 s press LED ×3, then SWING ×3; a 2 s beep confirms. LED shows the next item, SWING the previous one. Each item's name shows for 2 s, then its value for 25 s. Items: T1, T2, T3, T4, TP, FT (target Hz), Fr (actual Hz, printed TR), dL (current), Uo (AC volts), Sn (capacity test),--(running mode), Pr (outdoor fan), Lr (EXV), Ir (indoor fan), HU, TT, dT, IF (Wi-Fi), oT.Each code has a new 4-character equivalent on current Midea units (e.g. E1=EL01).
Codes in the 2018 service manual
E0 Indoor EEPROM parameter error E1 Indoor ↔ outdoor communication error E3 Indoor fan speed out of range E4 Room sensor T1 open or short E5 Indoor coil sensor T2 open or short Eb Indoor PCB ↔ display board communication error EF Intelligent-eye module error F0 Overload current protection F1 Outdoor ambient sensor T4 open or short F2 Outdoor coil sensor T3 open or short F3 Discharge sensor TP open or short F4 Outdoor EEPROM parameter error F5 Outdoor fan speed out of range P0 IPM malfunction or IGBT over-current P1 Over- or under-voltage P2 IPM high temperature P4 Inverter compressor drive error
Codes added in Midea's 2019 list of the old system
Vivax T Design (ACP-…LCTI)
- T Design
How to read codes on this unit
The indoor display shows the code. The owner's manual has no lamp table and no self-diagnosis mode. These codes are not the Midea ones: here E1is the room sensor, not communication.The manual button on the indoor unit starts forced operation, meant for testing and emergencies.
Display codes
E1 Indoor room temperature sensor fault E2 Indoor pipe temperature sensor fault E3 Outdoor pipe temperature sensor fault E4 Refrigerant leak or refrigerant system fault EY Refrigerant leak detected E5 Indoor fan motor fault E6 Outdoor ambient temperature sensor fault E7 Indoor ↔ outdoor communication fault E8 Outdoor discharge temperature sensor fault E9 Outdoor IPM module fault EA Outdoor current detection fault EE Outdoor PCB EEPROM fault EF Outdoor fan motor fault EH Outdoor suction temperature sensor fault